Tel: +86-132-0571-7266Email: sales@zhesock.comWorldwide Shipping
Get Free Quote
Quality

Sock AQL Inspection Guide: Sample Size and Defects

Published: 2026-07-23By ZheSock TeamReading time: 5 min
Sock AQL Inspection Guide: Sample Size and Defects

Sock AQL inspection is the buyer-side check that decides whether a packed sock order can ship. It uses sample size, defect grading, and fixed accept or reject numbers. The useful work starts before the inspector arrives. Define holes, shade bands, wrong size ratios, barcode errors, and packing mistakes in writing. A 10,000-pair order can pass or fail on 200 checked pairs under General Inspection Level II, so the rules must be clear.

Table of Contents

What sock AQL inspection means on a real order

Sock AQL inspection usually follows ANSI/ASQ Z1.4 or ISO 2859 sampling logic. It is normally done when production is 100 percent finished and at least 80 percent of cartons are packed. The inspector pulls cartons at random, checks pairs against the approved sample and purchase order, then applies the AQL accept and reject numbers.

AQL does not mean zero defects. It is the maximum defect level accepted by the sampling plan. A common retail setup for sock AQL inspection is Critical 0, Major 2.5, Minor 4.0. Critical 0 means one critical defect can fail the lot. With a 200-pair sample at Major 2.5, 10 major defects pass and 11 fail.

Put the inspection rules in the purchase order before yarn booking. Include style number, size ratio, color ratio, yarn content claim, needle count, packing method, carton marks, barcode file, and approved sample date. If the inspector receives only a photo and a packing list, too much judgment happens at the factory table.

How to choose sample size for socks

Sample size comes from lot quantity and inspection level. It is not a flat percentage. Most importers use General Inspection Level II for final sock AQL inspection. Special levels can work for carton drop checks or label checks, but they are too light for first orders, new yarns, new artwork, or retail programs with chargebacks.

This is why AQL sample size for socks must be set before shipment booking. ZheSock starts custom sock orders from 100 pairs, but sampling still matters on small lots. A 300-pair launch order with jacquard logo, dyed yarn, and retail header cards should not be reduced to opening one carton. For multi-color orders, the sample must cover every color and every size on the packing list.

Defect grading for sock buyers

Sock defects classification must match how the sock is sold. A basic 144-needle cotton crew sock has different risk from a 200-needle dress sock or a compression sock with size bands. Write limits in millimeters, grams, and counts. Vague terms cause disputes.

Use measurable rules. A toe linking skip over 3 mm is major. Leg height difference over 10 mm within a pair is major for retail socks. A jacquard logo shift over 5 mm is major when the logo is visible on the outside leg. A carton with the wrong size ratio is major even if the socks look fine.

Measurements inspectors should record

The inspector should measure against the approved pre-production sample and the size spec sheet. For adult crew socks, common checkpoints are foot length, leg height, welt height, relaxed cuff width, stretched cuff width, pair weight, and logo position. A practical tolerance is plus or minus 5 mm on foot length and leg height, plus or minus 3 mm on welt height, and plus or minus 3 percent on pair weight. Compression socks need pressure testing by size band, not only flat measurement.

Needle count changes the result. Common sock machine counts are 96, 120, 144, 168, and 200 needles. A 96-needle sock is thicker and shows rougher detail. A 144-needle sock is common for cotton crew socks. A 168 or 200-needle sock gives finer jacquard and dress sock detail, but yarn quality and tension control must be tighter.

GSM can be checked from a cut swatch after boarding, but pair weight is usually the clearer sock quality control point. As a rough reference, lightweight dress socks may be 180 to 260 GSM, cotton casual socks may be 220 to 420 GSM, and terry sports socks may be 350 to 650 GSM depending on yarn and terry depth. Record actual values. A pass mark alone is weak evidence.

When to inspect during production

Final inspection is late. For many private label sock orders, sampling, yarn booking, knitting, linking, boarding, pairing, labeling, and packing take 20 to 35 days after artwork and color approval. Small repeat orders may ship in 12 to 18 days when yarn is in stock. New dyed yarn, silicone grip print, gift box packing, or compression testing can add 7 to 15 days.

A practical control plan has three checks. First, approve yarn color, lab dip, artwork, and size spec before bulk knitting. Second, check the first 300 to 500 pairs from bulk machines for length, shade, logo position, terry placement, and stretch recovery. Third, run final sock inspection before shipment after packing, with carton quantity and shipping marks included.

Inline checks reduce rework. If the first bulk jacquard logo is stretched by 8 mm, the knitting program can be corrected before thousands of pairs are boarded. If anti-slip dots are curing poorly, the print shop can change temperature or dwell time before the socks enter retail packing.

Cost, MOQ, and how to lower failure risk

Inspection cost is usually smaller than failure cost. A third-party inspection in China often costs USD 180 to USD 320 per man-day. Rework for trimming, re-pairing, relabeling, or repacking often costs USD 0.03 to USD 0.12 per pair. Reprinting wrong barcodes or replacing header cards can cost more than the knitting profit on a basic sock.

Price and construction affect risk. A basic private label cotton crew sock is often around USD 0.55 to USD 1.20 per pair depending on yarn, size, needle count, and order volume. Terry sports socks with arch support and silicone anti-slip print often run about USD 1.10 to USD 2.80 per pair. Compression socks with tested pressure bands can be higher. ZheSock MOQ starts at 100 pairs, but custom dyed yarn, special packaging, or 200-needle production may require higher color minimums.

Reduce AQL failure by sending one clear tech pack. Include fiber content, needle count, target pair weight, size chart, Pantone or lab dip, logo file, barcode file, packing ratio, carton size, and defect photos. Ask for OEKO-TEX documents when chemical safety claims matter. ZheSock is OEKO-TEX certified. Buyers can also request factory audit documents such as BSCI, Sedex, ISO 9001, GOTS, GRS, or CE when they apply to the program.

Frequently Asked Questions

What AQL level is common for sock inspection?

Many sock buyers use Critical 0, Major 2.5, Minor 4.0 under General Inspection Level II. For a 200-pair sample, Major 2.5 passes with 10 major defects and fails at 11. Baby socks, compression socks, and retailer programs with strict chargebacks may need tighter limits.

Is sock AQL inspection the same as checking 10 percent of the order?

No. AQL sample size comes from the lot size and inspection level. A 10,000-pair order under General Level II uses a 200-pair sample, which is 2 percent of the order. A 500-pair order uses a 50-pair sample, which is 10 percent. The table controls the sample size.

Should every sock color and size be sampled?

Yes. Each color and size should appear in the random sample when they are part of the order. Shade bands, wrong labels, and packing ratio mistakes often happen by color lot or size carton. If one color is only 5 percent of the order, the inspector should still open cartons from that color.

Which sock defects usually fail a shipment?

Common failure causes are toe holes, dropped stitches, broken elastic, wrong size stickers, wrong barcodes, missing hangtags, heavy stains, poor pair matching, and carton quantity errors. One critical defect can fail the lot when the contract states Critical 0. Major defects fail the lot when the count reaches the reject number in the AQL table.

Can the factory inspect socks instead of a third party?

Factory inspection is useful during knitting, linking, boarding, and packing. It should not replace buyer-side AQL checks for first orders, new suppliers, new yarns, or retail shipments. A third-party report gives the buyer an independent record before balance payment or shipment release.

Related Searches
sock AQL inspection checklistAQL sample size for sockssock defects classificationsock quality control standardssock inspection before shipmentmajor and minor defects in socks

Looking to Launch Your Custom Sock Line?

ZheSock is a Zhejiang-based OEM/ODM sock manufacturer with 17 years of export experience. Free design, low MOQ from 100 pairs, OEKO-TEX certified.

Get Free Quote Now »

Related Articles

EU Sock Fiber Label Rules for Private Label Importers
Quality2026-07-23

EU Sock Fiber Label Rules for Private Label Importers

Check EU sock label basics for fiber names, percentages, origin text, care symbols and importer data before retail packi...

Read More »
Sock Quality Control Explained: AQL 2.5, In-Line Inspection, and Defect Standards
Quality2026-04-22

Sock Quality Control Explained: AQL 2.5, In-Line Inspection, and Defect Standards

How a professional sock factory runs quality control: AQL 2.5 sampling, in-line and end-line inspection, defect classifi...

Read More »
How to Audit a Chinese Sock Factory Remotely
Quality2026-06-09

How to Audit a Chinese Sock Factory Remotely

Use video checks, document requests, and production proof to vet a sock factory in China before you place a large B2B or...

Read More »